Invalid partition table

Solution 1 of 4 - Change Boot Media

If you are booting from either a DVD, CD, diskette or a USB drive, remove the media and boot from the hard disk. The media is either damaged or is not intended to be bootable.

Solution 2 of 4 - Update the BIOS and BIOS Parameters

Check with the PC manufacturer if you're using the latest BIOS or not. If not, update to the current version.

A few of the manufacture's download sites for a motherboard/BIOS update:

If the BIOS is current, it's possible bad BIOS parameters are causing the problem, especially if the memory or CPU settings are overclocked. The BIOS parameters are stored in CMOS memory. The best way to reset the BIOS parameters is to remove the CMOS battery. To do this:

1. Unplug the PC, and open the case.
2. Locate the battery on the motherboard - typically a silver coin cell.
3. Remove the battery and note if the plus side is up or down, so you can reinstall it later the same way.
4. Wait at least 1 minute and reinstall the battery.
5. Attach power and power up. Typically a BIOS warning message will indicate CMOS was corrupted or changed and it may require you to go into the BIOS setup to set the time and date.
6. Proceed to boot Windows and see if this fixes the issue.

Some BIOSes have options to enable/disable caching and/or shadowing. If the options are available, disable caching and shadowing. Most newer (2005+) systems do not have these options. There are many BIOS makers and customized versions of the BIOS, so you may have to enter BIOS setup and look a bit to find these options. Typically you press a key like Esc, Del, F1, or F2 before Windows starts (almost right after you reboot) to enter BIOS setup. Consult your computer manual for details. The setup key can also be found in our BIOS access list.

Solution 3 of 4 - Replace MBR and Fix Partition Table

It's possible the code is damaged in the MBR (Master Boot Record) or the partition table is damaged. While the code can be easily fixed, a damaged partition table may not be repairable.

If you have a graphical partitioning boot CD, such as Partition Commander, System Commander, Fix-It Utilities Professional or SystemSuite Professional, we suggest using it. These tools can validate the partitions, it's fast and it can fix a some issues not possible with the Windows solutions. Using these tools, you'll replace the MBR with a Generic MBR (In manual partitioning, Advanced). You'll also make sure the one partition with your OS is set bootable. Click on the OS partition and check Under the General tab. It should be marked as Active. If not, go to the menu Advanced, select Set/Toggle Bootable/Active. Under the General tab, you should now see "Active". Remove the boot media, exit and reboot.

You can also replace the MBR from a command prompt. You'll need to boot from the Windows CD/DVD and go into the Vista Recovery Console or XP Recovery Console and select Command prompt. Follow our instructions under recovery console to repair the MBR (instructions differ between Vista and XP).

Replacing the MBR does NOT change the partition table, so if it's damaged, it will not be fixed.

Once working, be sure to do an extensive scan for viruses and malware.

Solution 4 of 4 - Last resort solutions!

If you skipped any of the prior solutions, you may want to return and try them out. These next options are when all else fails!

• Remove the system hard drive and replace it with a blank drive. Install a fresh copy of Windows. If this works, it's unlikely to be a hardware issue. At worse, it may be time to start over with a fresh copy of Windows, although reinstalling your applications may make the problem reoccur.
• Send the PC in for repair - someone else can deal with it!
• Time for a new PC?
• Consider a MAC, but wait - they can have similar hard-to-solve issues and you'd have to buy all new applications.
• Use your PC as a boat anchor and go for a drink.

Check out what others say about this issue and review or add your own comments and solutions!